PureTherm Energy Solutions Ltd
← All news

9 November 2026

Commercial Boiler Servicing: What Facilities Managers Should Expect

Commercial Boiler Servicing: What Facilities Managers Should Expect

Commercial gas engineer carrying out a boiler inspection in a plant room

Commercial boilers should usually receive a full service at least once a year, following the manufacturer’s instructions. Higher-load or safety-critical plant may need more frequent attention, depending on its condition and how it is used. A proper visit is more than a quick visual check: it should include appropriate safety and combustion checks, inspection of the flue and controls, and a clear written report of findings and follow-up work.

For facilities managers, a planned servicing regime helps keep equipment safe, maintainable and less likely to fail without warning. It also gives you a useful record of what was checked, what needs attention and who is responsible for closing out defects.

How often should a commercial boiler be serviced?

Annual servicing is a sensible starting point for many commercial systems, but there is no single legal interval that applies to every commercial boiler. The service frequency should reflect the manufacturer’s instructions, system condition, operating hours, load and the consequences of an outage.

A boiler running for long hours, serving a busy site or supporting a critical process may need more frequent checks than lightly used plant. Your commercial heating maintenance plan should set out the frequency for each asset, rather than applying one interval across an entire site by default.

Under the Gas Safety (Installation and Use) Regulations 1998, duty holders must ensure gas fittings are maintained in a safe condition. The HSE’s guidance for employers says gas appliances, pipework and flues should be regularly maintained, and that gas work must be carried out by a Gas Safe registered engineer or other competent person where the regulations allow.

Check that the engineer’s registration and qualifications cover the specific commercial gas work. A domestic gas qualification alone does not establish competence for every commercial appliance.

What should a proper service visit include?

The scope should follow the boiler manufacturer’s instructions and suit the equipment on site. The contractor should identify the assets being serviced and record what was actually examined, tested and found.

Commercial plant room equipment with insulated pipes, valves and control panels

A typical visit may include:

  • Combustion and burner checks: combustion analysis using a suitable calibrated analyser, with readings compared against the manufacturer’s requirements. The engineer should investigate readings outside the specified range before returning the appliance to service.
  • Flue and ventilation inspection: checking the flue, air supply and ventilation for condition, obstruction or other issues that could affect safe operation.
  • Safety devices and interlocks: testing relevant controls and proving that the boiler shuts down safely when required. Site-specific interlocks may include ventilation, gas isolation or other plant controls.
  • Gas installation checks: examining accessible pipework, valves and connections, and checking for leaks where appropriate to the work.
  • Boiler condition and cleaning: inspecting and cleaning components where the manufacturer’s procedure requires it, and checking the heat exchanger, seals and condensate arrangements on condensing boilers.
  • Controls and operation: checking operating controls and set points, and reviewing boiler sequencing or BMS interaction where these form part of the agreed scope.
  • Heating circuit checks: reviewing system pressure and the operation of pumps and valves. The service plan may also include checks on water quality, inhibitor levels or magnetic filtration, depending on system design and condition.
  • Plant-room condition: noting access, ventilation, leaks, corrosion, poor insulation or other conditions that may affect safe maintenance or reliable operation.

The engineer should explain any limitation (for example, if equipment cannot be safely accessed or a required test cannot be completed) and agree what happens next.

What records and certificates should I expect?

Ask for a written report linked to the equipment or asset reference. It should identify the date, engineer, work completed, relevant readings, defects, parts replaced and recommendations, along with the appliance’s safety status and any actions still outstanding.

The type of record depends on the premises and the duty involved. A landlord’s formal Gas Safety Record applies to relevant residential landlord duties; it is not automatically the required document for every wholly non-residential boiler. For commercial sites, keeping service reports, inspection findings, repairs and close-out records creates a practical maintenance history and helps demonstrate that defects have been managed.

If the plant serves residential accommodation within a mixed-use building, check which landlord gas safety duties apply. The HSE’s guidance on maintenance and gas appliances explains the separate maintenance and record-keeping considerations for landlords.

What is the difference between PPM and reactive maintenance?

Planned preventative maintenance (PPM) is scheduled work carried out before a failure occurs. Reactive maintenance is work undertaken after a fault, breakdown or safety concern has been reported.

A sensible PPM schedule is based on the equipment, manufacturer guidance and site risk. It could include:

  • A full boiler service at the agreed interval, commonly annually as a starting point.
  • More frequent checks for heavily used, older or critical plant, where the system condition and risk justify them.
  • Routine checks by trained site staff, with a clear process for reporting fault codes, leaks, unusual operation or suspected gas issues.
  • A review of outstanding recommendations, access requirements and asset records at planned intervals.

PPM cannot prevent every breakdown, but it can help identify deterioration and recurring problems before they become an emergency callout. A commercial HVAC maintenance contract should make the scope, attendance arrangements, reporting and responsibility for remedial work clear.

What common plant-room issues should an FM watch for?

A boiler service is one part of looking after the wider heating system. Plant-room visits may also identify issues that affect heat delivery or make faults harder to diagnose, such as restricted circulation, ageing valves or actuators, and controls that no longer reflect the building’s operating hours or current use.

Engineer checking commercial heating controls, a pump and pipework

For example, poor circulation can affect system performance even when a boiler itself appears to operate. Worn components or control settings that do not suit the building can also contribute to uneven heating or unnecessary cycling. These are typical items to investigate, not automatic proof of a particular fault.

The useful report tells you what was observed, what evidence supports the recommendation, and whether the issue is urgent, safety-related or suitable for planned follow-up.

What should I expect from a maintenance contractor?

A competent contractor should agree the work before attending and provide a clear record afterwards. Look for:

  • A fixed, asset-based schedule with responsibilities and visit scope set out.
  • Gas Safe registration and relevant competence for the commercial appliances involved.
  • Transparent fault finding, including an explanation of the checks carried out.
  • Clear separation between essential remedial work and recommendations for future planning.
  • A named point of contact and a practical process for urgent faults.
  • Reports that identify defects, safety status and actions needed to close them out.

Good communication matters, especially where a plant room is shared with other contractors or serves occupied areas. The contractor should follow site rules and explain any equipment they have isolated or left out of service.

Can a contractor support communal heating and M&E work?

Commercial heating maintenance may also cover communal heating systems, heat networks and energy centres, where boilers are only one part of the installation. Pumps, valves, controls and distribution equipment all affect the performance of the system and may need to be included in the agreed maintenance scope.

Engineer surveying a communal heating energy centre and insulated pipework

PureTherm supports facilities managers, property managers, heat-network operators, M&E contractors and heat-pump companies with commercial boiler repair, plant-room maintenance, PPM, reactive fault finding and subcontract engineering support. The team works across Hertfordshire, Bedfordshire and London, including Letchworth Garden City, Hitchin, Stevenage, Baldock, Welwyn Garden City, Hertford, Royston, Biggleswade and Bedford.

PureTherm is an owner-led independent business with over 30 years of heating and HVAC experience. The company is Gas Safe Registered (978743), F-Gas qualified and fully insured, with direct contact with the engineer from initial discussion through the work.

Frequently asked questions

How often should a commercial boiler be serviced?

Usually at least annually as a starting point, but follow the manufacturer’s instructions and adjust the interval to suit the plant’s load, usage, condition and risk.

What is the difference between PPM and reactive maintenance?

PPM is planned work intended to check and maintain equipment before failure. Reactive maintenance responds to a breakdown or reported fault.

Do you offer planned maintenance contracts?

PureTherm can discuss a maintenance arrangement based on the equipment, site requirements and agreed scope. The schedule should reflect the actual system, rather than assume one frequency fits every asset.

Can you support heat networks and communal systems?

Yes. Support can include plant rooms, energy centres, pumps, valves, controls, communal heating and heat-network equipment.

Do you subcontract for M&E contractors?

PureTherm provides subcontract engineering support for M&E contractors and other heating and heat-pump companies. Scope and site requirements can be discussed directly with the engineer.

If you are reviewing a maintenance contract or want to discuss a plant-room visit, contact the PureTherm engineer for a straightforward conversation about your site and its requirements.